In case of fire, the link is melted and the door will roll or slam shut. NFPA 82 Section 6 has similar requirements for the chute intake door operation and latching mechanism as well as size limitations for the intake door. Trash chutes for apartments are long, vertical shafts that allow the trash to be disposed of on each floor . The intake on each floor often has a door to heighten safety measures. As residents dispose of their trash, it accumulates at the bottom in a dumpster or goes through a trash compactor. High-rise apartment buildings have dense populations, which means a ton of trash can accumulate quickly.
Chute intake doors may be certified for installation in concrete and masonry shaft walls or non-masonry shaft walls. The specific construction type permitted for a certified intake door will be noted in the product certification information. It is important to specify and verify that the correct intake door is installed based on the construction of the shaft wall used for the linen or waste chute. Chute-type fire doors must always horizontal rolling discharge chute outlet door be installed in accordance with the manufacturer’s instructions and should be included with construction documents. This is our most popular Horizontal Rolling Discharge Door or sometimes called a Guillotine discharge door, and is mainly an outlet shoot door for an internal garbage solution. The NFPA requires all internal chutes to have discharge doors that are held open by a fusible link, and this door fulfills that requirement.

Call us and let us set up a plan to ensure that your garbage chute, compactor, bagger, or recycling chute continue to operate in peak condition. A shaft enclosure containing a waste, recycling, or linen chute shall be constructed of materials as permitted by the building type of construction. Nearly every maintenance person uses the door at the bottom of the chute to stop garbage falling on the floor when the dumpster is being emptied. But this door—called a guillotine or discharge door—is actually a fire damper door.
To help control potential noise, a sound dampening material can be applied to the outside of the metal chute. When combined with our internal trash chutes in multi-story buildings, the DuraSorter™ recycling sorter provides an easy method for sorting recyclables out of the waste stream. You can prevent many of the recyclable materials from entering the environment and reducing the negative impact that comes with contentious property manager. The system can be used in either new construction projects or installed as a retrofit to an existing trash chute system. By providing 2-hour fire-resistance-rated construction as described, the proposed design exceeds the code requirements, and we request that the proposed design be approved.

The chute system can allow access at every floor and roof levels and deposits the trash into the dumpster at the bottom. CHUTES heavy-duty steel chute is perfect for heavy demolition and the DURACHUTE plastic system is perfect for lighter demolition, roof work, new construction and special applications like snow removal, landscaping, etc. Wilkinson Hi-Rise trash chutes are constructed of #16 gauge aluminized steel, galvanneal and several different grades of stainless steel. By the way… There are multiple documented incidents of compromised trash chute doors, not unlike the obstruction in the picture, that lead to catastrophic, tragic fires in hospitals, with great loss of life.
Each floor's intake doors are sized to the dimension of the trash or linen chute. The intake doors feature all stainless-steel doors, are self-closing, self-latching, and have a protected closer. These doors are UL labeled, which are rated at 1.5 hours with a maximum temperature rise of 250 degrees in 30 minutes. Chutes are intended for multi-level buildings and can be used for trash, linen or recycling. Chutes are fully factory assembled with all joints welded and there is a minimum of one expansion joint per floor with a flush interior assembly without bolts, rivets or clips.

These chutes are made standard of impact and corrosion resistant plastic.Trash Chute Door Standard hand operated intake, noiseless, self-closing, side or bottom hinged, 11/2 hour, 250°, U.L. It is industry standard to have a discharge door at the bottom of internal trash chute and linen chutes systems. These doors offer a level of fire protection that most inspectors require.
Because these doors are required to carry a “B” label, 1 1/2 hour rated assembly, they will also have a positive latch with a hand operated door control and a metal frame suitable for enclosing the chase. These doors can have an electric interlock which allows only one door to be in use at any given time and keeps the other intake doors positively locked at all times except during use. As with our linen chutes, our trash chutes are better looking, longer lasting, easier to clean, and require less maintenance. Our trash chutes are also outfitted with the only intake door on the market with both front and back stainless panels and skirts. Our internal trash chutes are designed to fit the exact specifications of each building they are installed in therefore pricing on this product is based on the the specific details of the application.
Have you ever thought about what happens when the doors of a trash chute are opened? It’s definitely something you should be thinking about and be aware of. Recent studies have discovered the inner surface of a chute can carry more than 30 different biological and bacterial growths. If a trash chute doesn’t receive proper and timely cleaning care, all of these germs and bacteria become airborne every time the chute doors are opened. These bacteria carry all kinds of illnesses and infections throughout the building, potentially affecting occupants.

Any backup of materials could also cause damage to the chutes and also create a fire and smoke hazard as well. Automatic Brush Cleaning System, A cylindrical housing with replaceable stiff nylon brushes is automatically lowered and raised by a geared electric motor. The nylon brushes scrape and clean the internal surface as they move down and up the chute. The water supply for flushing the chute, the electric motor and the built in safety overloads, are all individually controlled by a robust electric logic control. A Trash/Linen/Garbage/Rubbish chute may differ from a Linen chute primarily in the way it terminates at the bottom, where the Garbage chute end into a trolley. Hotels and hospitals that use Linen chute install sorting tables at the bottom end of the chute to ensure that Linen can be sorted as it is received.